Vitapur VPL-8 Manuel d'instructions télécharger pdf (Page 5)

When handling the UV lamps and quartz sleeves, soft gloves or a cloth should always be used

to prevent oil deposits on the surface. Oil deposits from your hands can create hot spots on the

surface which may lead to premature bulb failure.

• DetermineasuitablelocationandensuremountingoftheUVsysteminthecorrect

orientation can be completed.

• Attachthemountingclamptotheinstallationstructureusinganappropriatescrew

type for both the weight and material of the surface.

• PositiontheUVreactionchamberintothemountingclampandsecure.

• Installallinlet/outletplumbingtothesystem(inclusiveofallpre-ltrationand

valve set-ups described above.

• MounttheelectronicballastinadrylocationclosetotheUVreactionchamber.

• Ensurethequartzsleeveisintactandthatbothsiliconeo-ringsandglandnutsare

in position and tightened (do not overtighten the gland nuts, these should be hand

tightened only)

• ConnectthefourpinsoftheUVlamptotheUVlampplugontheballast

• InserttheUVlampintothequartzsleeveandsecuretheprotectivecover

• SlowlyopenthesupplyvalvesbeforeandaftertheUVsystemandensurethere

are no water leaks.

• Connecttheelectronicballasttothepoweroutlet,andensurethatthegreenlight

turns on.

Your UV disinfection system is now ready for use.

In-House Water Distribution System Disinfection

The following procedure is recommended for installations of the vitapur

disinfection system in a whole house treatment application. For point of use

applicationswheretheVPL-2systemisbeingutilized,asimilarprocedureshouldbe

followed to ensure all downstream plumbing from the treatment system is disinfected

prior to initial use. For systems installed on a municipally treated water system,

plumbing system disinfection is at the discretion of the user.

To disinfect the distribution system, carry out the following steps (please ensure that

theUVsystemremainsonduringtheentireprocess):

• Familiarizeyourselfwiththevariousshut-offvalvesonyoursystem.Itisimportant

to understand which combinations of valve positions allow you to isolate the

vitapur

UV disinfection system

• Shutthemainwatersupplyoffanddrainthehotwatertankandanyotherstorage

tanks that may be downstream of the pre-ﬁlter ﬁlter housing.

• Closethevalvesnecessarytoisolateandremovethesedimentltercartridge.

 Removetheltercartridgefromthehousingsandllthesumpwith1-2cupsof

 householdchlorinebleach(5.25%).

• Re-installthesump(withoutlter)andslowlyre-pressurizethesystem.Openall

faucets and allow cold water to run until you can smell chlorine in the water. Shut

off the faucet and repeat with all other household faucets. Be sure to include all

exterior faucets, shower heads, and dishwasher / washing machine lines within

this process.

• Allowthesolutiontoremaininthelinesfor30minutes.

• Re-installthepre-ltercartridge,andusheachindividualwaterlineasabove

until no chlorine odor is detected. It is critical to ensure that the water distribution

 systemisfullyushedofallresidualchlorinepriortouse.EXTREME CAUTION

SHOULD BE EXERCISED. As the level of chlorine in the system is approximately

 25-50timesgreaterthanthatobservedinmunicipallytreatedwater(thisis 

required for the disinfection of the household lines). It is extremely important that

 properushingproceduresbefollowedfromalltapspriortouse.

Note: The introduction of a chlorine disinfection solution to a hot water heater that

has been used with untreated hard water or water with excessive iron, manganese or

other organic contaminants may lead to oxidization of these materials. If you feel that

these conditions may apply to your installation, a thorough ﬂushing of the hot water

tank should be done to eliminate the oxidized material from the system.

Operation & Maintenance

The UV system should remain on continuously to ensure protection of your water

system.Duringnormaloperationofthesystem,thegreenpowerLEDlightwillbe

illuminated.

Duringperiodsofnon-use,itisnormalforthetemperatureofthewaterinthe

cylindertorise.Simplyushingthewaterlinewillalleviatethiscondition.During

humid conditions, sweating, or small water droplets may be noticed on the surface

of the UV reaction chamber. The formation of condensation during high humidity

conditions is normal.

The following instructions have been provided to assist with general maintenance

of the system; UV lamp replacement and quartz sleeve cleaning/ replacement.

All other system repairs must be completed by an accredited service technician.

1 2 3 4 5 6 7 8 9 10 ... 20 21

Commentaires sur ces manuels

Pas de commentaire

Vitapur VPL-8 Manuel d'instructions Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Non Vitapur VPL-8