Vitapur VPL-8 Manuel d'instructions télécharger pdf (Page 6)

An accredited service technician can be located by visiting our website at www.

greenwayhp.com or by calling our Customer Service Center at 1-866-253-0447.

WARNING: Never attempt to service the vitapur

UV system unless you are an

accredited service technician, as the performance of the system could be adversely

affected.

5.1 Lamp Installation and Replacement

WARNING: The lamp heats up after continuous use and can burn your skin if

touched. Allow lamp to cool for at least 5 minutes before removing. Do not operate

the UV lamp outside of the reactor. The lamp in the unit emits Ultraviolet light that

can cause permanent damage to skin and eyes. Never look at the lamp when the unit

is turned on. Handle the UV lamp by the ends only. Do not touch the bulb of a lamp

with your ﬁngers. If the surface of the lamp becomes dirty, use a clean lint-free cloth

and glass cleaner to remove the dirt.

Your vitapur

UV disinfection system is equipped with a visible / audible lamp failure

indicator.IntheeventofafailureoftheUVlamp,theredLEDlightwillashanda

loud beeping will be audible from the electronic ballast of the unit. Please note that

if these conditions occur and you are on a non-municipal supplied water source, you

should immediately stop using the water for potable applications until the lamp is

replaced and disinfection of the distribution lines is completed.

Theultravioletlamphasanapproximatelifeofoneyear(9000Hrs.).Replacement

UVlampsandquartzsleevesareavailablefromanauthorizedretailerandGreenway

HomeProducts.Useonlyvitapur

lamps and sleeves to ensure system performance.

Replacement lamps and quartz sleeves are sold as a combined replacement kit

underthefollowingmodelnumbersandcanbeorderedonlineatgreenwayhp.com:

 VUVL-2–replacementlampandquartzsleeveforVPL-2

 VUVL-6–replacementlampandquartzsleeveforVPL-6

 VUVL-8–replacementlampandquartzsleeveforVPL-8

 VUVL-12–replacementlampandquartzsleeveforVPL-12

Procedure for Replacing / Installing the Ultraviolet (UV) Lamp:

• Turnoffthewatersupplyatbothendsofthesystem.

• Unplugtheunit.

• DrainwaterfromtheStainlessSteelUVChamber.

• Allowatleast5minutesforlamptocool.

• RemovetheconnectorfromtheendoftheUVlamp.

• RemovetheUVlampfromthequartzsleevebygentlyrotatingthelampfree.Be

sure to hold the lamp only by the ceramic tips.

• InsertthenewUVlampintothequartzsleeveandattachtheconnector.

• RelltheUVchamberbyopeningthewatersupplyjustenoughtollthechamber

with water.

• Checkthesystemforleaks.

• EnsurethattheUVlampisoperating–thegreenpowerLEDlightshouldbe

 illuminated,theredlampfailureLEDlightshouldbeoffandnoaudiblealarm

should be active.

Mineral deposits and sediment build-up on the quartz sleeve will affect the system

performance by decreasing the UV light transmitted through the quartz sleeve into

the water column.

The proper maintenance and replacement of the pre-ﬁltration required for the UV

system will reduce the accumulation of mineral and sediment residue on the quartz

sleeve.

The quartz sleeve may be cleaned with a commercially available, non-abrasive, scale

remover (should be acidic) and a lint free cloth. Cleaning of the quartz sleeve should

be done on a regular basis to ensure maximum system performance. The amount of

cleaning required will vary dependant upon local water conditions.

All traces of the cleaning solution must be fully removed from the sleeve before it is

reinstalledinthesystem.Careshouldbetakentopreventanycleaninguidfrom

coming into contact with the inside surface of the quartz sleeve.

Procedure for Removing / Installing the Quartz Sleeve:

• Turnoffthewatersupplyatbothendsofthesystem.

• Unplugtheunit.

• DrainwaterfromtheStainlessSteelUVChamber.

• Allowatleast5minutesforlamptocool.

• RemovetheconnectorfromtheendoftheUVlamp.

• RemovetheUVlampfromthequartzsleevebygentlyrotatingthelampfree.Be

sure to hold the lamp only by the ceramic tips.

1 2 3 4 5 6 7 8 9 10 11 ... 20 21

Commentaires sur ces manuels

Pas de commentaire

Vitapur VPL-8 Manuel d'instructions Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Non Vitapur VPL-8